Request For Quotation

Request For Information

Automotive scope ATS5004D


Manufacturer: Tiepie show products

The compact and powerful Automotive scope ATS5004D features a SureConnect connection test and resistance measurement, making it the perfect tool for an automotive engineer to diagnose automotive problems.

Description

The compact and powerful Automotive scope ATS5004D features a SureConnect connection test and resistance measurement, making it the perfect tool for an automotive engineer to diagnose automotive problems.

Key specifications:

Oscilloscope / Spectrum analyzer / Multimeter / Data logger
12, 14, 16 bit resolution
50 MS/s sampling
50 MHz bandwidth
128 KSamples memory per channel
100 ppm time base accuracy

Features

Safe measuring using differential inputs:
The Automotive scope ATS5004D is a four channel automotive oscilloscope with differential inputs. With the differential inputs it is possible to measure four totally unrelated signals simultaneously.
SureConnect on each channel:
The SureConnect connection test feature of the Automotive scope ATS5004D tells you immediately whether your test probe or clip actually makes electrical contact or not. No more doubt whether your probe doesn't make contact or there really is no signal.
This is useful when surfaces are oxidized and your probe cannot get a good electrical contact. Simply activate the SureConnect and you know whether there is contact or not. Also when back probing connectors in confined places, SureConnect immediately shows whether the probes make contact or not.
Resistance measurement on each channel :
Many automotive sensors are based on variable resistors. Use your Automotive scope ATS5004D in the resistance setting to test them, no more need to take a separate ohm meter. Resistance values can be displayed as a number, but it is also possible to display the resistance variation in time, in a graph.
Fully supported by ATIS:
All features of the Automotive scope ATS5004D are fully supported by ATIS, the Automotive Test and Information System. Select a specific diagnostic measurement in ATIS, click the measure button and the Automotive scope ATS5004D will be completely setup for that specific measurement and ready to perform it.

Specifications

Acquisition system 
Number of input channels 4 analog
Ch1, Ch2, Ch3, Ch4 BNC
Type    Differential
Resolution 12, 14, 16 bit user selectable
Accuracy 0.3 % of full scale ± 1 LSB 
Ranges     200 mV to 80 V full scale
Coupling AC/DC
Impedance 2 MOhm / 40 pF
Maximum input voltage (in all ranges) ±200 V (DC + AC peak < 10 kHz)
with 1:10 attenuator ±300 V (DC + AC peak < 10 kHz) 
Maximum Common Mode voltage 200 mV to 800 mV ranges : 2 V
2 V to 8 V ranges : 20 V
20 V to 80 V ranges : 200 V
Common Mode Rejection Ratio -48 dB
Bandwidth (-3dB) DC to 50 MHz maximum 
AC coupling cut off frequency (-3dB) 1 Hz 
Channel Isolation    500 V
Channel Separation -80 dB 
SureConnect
Maximum voltage on connection 200 V (DC + AC peak < 10 kHz)
Resistance measurement
Ranges 100 Ohm to 2 MOhm full scale 
Accuracy 3% 
Response time (to 95%)  < 5 ms
Maximum sampling rate On all channels simultaneously 
12 bit 50 MS/s 
14 bit 3.125 MS/s 
16 bit  195.3125 kS/s 
Maximum streaming rate 10 kS/s 
Sampling clock source
Internal Quartz 
Accuracy ±0.01 %
Stability ±100 ppm over -40 °C to +85 °C 
Time base aging ±5 ppm/year 
External On extension connector 
Memory 128 KiSamples per channel 
Trigger
System    Digital, 2 levels
Source    CH1, CH2, CH3, CH4, AND, OR, digital external 
Trigger modes Rising edge, falling edge, inside window, outside window
Level adjustment 0 to 100 % of full scale 
Hysteresis adjustment  0 to 100 % of full scale 
Resolution 0.025 % (12 bits) 
Pre trigger  0 to 128 KiSamples, 1 sample resolution) 
Post trigger 0 to 128 KiSamples, 1 sample resolution) 
Digital external trigger
 Input Extension connector 
Range 0 to 3.3 V (5 V max)
Coupling

DC

Interface
Interface USB 2.0 High Speed (480 Mbit/s); (USB 1.1 Full Speed (12 Mbit/s) and USB 3.0 compatible)
Power Requirements
Power from USB port 500 mA max (2.5 W max)
Power via external power input / extension connector 1500 mA max (7.5 W max)
Minimum voltage 4.5 VDC
Maximum voltage 14 VDC
Physical
Instrument height  25 mm (1 inch)
Instrument length  170 mm (6.7 inch)
Instrument width  140 mm (5.2 inch)
Chord length  1.8 m (70 inch)
Weight  460 g (16 ounce)
I/O connectors
Channel 1...4 Isolated BNC
USB fixed cable with USB 2.0 and USB 1.1 type A connector
Extension connector D-sub 25 pins female
System Requirements
PC I/O connection USB 2.0 High Speed (480 Mbit/s); (USB 1.1 Full Speed (12 Mbit/s) and USB 3.0 compatible)
Operating System Windows 98/ME/2000/XP/Vista/7/8
Operating Environment 
Ambient temperature -20 to 70 °C
Relative humidity 10 to 90% non condensing
Storage Environment 
Ambient temperature -20 to 70 °C
Relative humidity 5 to 95% non condensing
Certifications and Compliances
CE mark compliance Yes
RoHS Yes
Package
Convenient carry case Carry case BB451
Instrument Automotive scope ATS5004D
Probe  4 x Measure lead TP-C1812B, BNC -> 4 mm banana jack
Accessories   4 x Differential attenuator TP-DA10 external power cable for second USB por
Software   Windows 98/2000/ME/XP/Vista/7 on CD
Drivers   Windows 98/2000/ME/XP/Vista/7 on CD
Manual   instrument manual and software user's manuals
color printed on paper and digital on CD 
Total Package weight   Approx. 3 kg